 |
|
 |
MBD-X7DBP-i-B |
|
| |
|
|
| Form Factor |
|
| Dimensions |
- 16.24" Length x 11.23" Width (41.25cm x 28.52cm)
|
| |
|
|
| CPU |
- Dual 771-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same
type below:
- Quad-Core Intel®
Xeon®Processor
5400/5300
sequence
(Harpertown
/Clovertown processor)
up to 3.16 GHz
- Dual-Core Intel®
Xeon®Processor 5200/5100/5000
sequence (Wolfdale
/Woodcrest/Dempsey processor) up to 3.40 GHz
|
| System Bus |
- 1333 / 1066 / 667 MHz system bus
|
| Operating System Software |
- Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
|
| |
|
|
| Memory Capacity |
- Eight 240-pin DIMM sockets
- Supports up to 32 GB 667/533MHz FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
|
| Memory Type |
- 667/533MHz FB-DIMM (Fully Buffered DIMM) ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 Single Device Data Correction (SDDC)
|
| |
|
|
| Chipset |
- Intel® 5000P (Blackford) chipset
- MCH + PXH + ESB2
|
| SATA |
- ESB2 SATA Controller
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
|
| IPMI |
|
| Network Controllers |
- Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT support for fast, scaleable, and reliable networking
|
| Graphics |
- ATI ES1000 controller with 16 MB of video memory
|
| Super I/O |
|
| Clock Generator |
|
| |
|
|
| Serial ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
| IDE |
- Single EIDE channel support up to two UDMA IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
| Floppy |
- 1 Floppy controller; 1.44 MB
|
| LAN |
|
| USB |
- 2x USB rear ports
- 2x USB internal headers, 1 dual, 1 single
- USB 2.0 Compliant / 1.1 Compliant
|
| VGA |
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Port / Header |
- 2 Fast UART 16550 serial ports
|
|
|
|
|
|
| 1U Chassis |
- CSE-816A-R700
- CSE-816A-700
|
| Important Chassis Notes |
- To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
|
| |
|
|
| Left Universal Slot |
- 1 (x8) PCI-e slot OR
- 1x 64-bit 100MHz PCI-X (3.3V) slot
|
| Right Universal Slot |
- 1 (x8) PCI-e slot OR
- 1x 64-bit 133MHz PCI-X (3.3V) slot
|
| IPMI |
- 1 SIM1U Slot (IPMI 2.0)
(Supermicro Intelligent Management)
|
| |
|
|
| BIOS Type |
- 8Mb Flash EEPROM with Phoenix® BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- SMBIOS 2.3
- APM 1.2
- DMI 2.3
- PCI 2.2
- ACPI 1.0
- ACPI 1.0 (limited)
- USB Keyboard support
- Hardware BIOS Virus protection
|
| |
|
|
| Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0 / 1.5 - with Virtual Media 8
- Optional KVM over LAN & 3rd LAN Port
- SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations |
- ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
|
| |
|
|
| Voltage |
- Monitors for CPU Cores, +3.3V, +5V, ±12V, +5V Standby, VBAT
- CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.86V-1.63V
|
| FAN |
- Total of ten proprietary fan headers for up to ten fans
- Ten fans with tachometer status monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
|
| Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x fan connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
|
| LED |
- CPU / System Overheat LED
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
|
| |
|
| Environmental Spec. |
- Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
| |
|
|
| FCC |
- Passed to meet FCC standard requirement
|
|
